Frequently Asked Questions
Powder coating is a fine dry powder coating material used for prepping, painting, and protecting a wide range of industrial, commercial, and consumer products. Powder coating is typically applied electrostatically using a powder coat gun or industrial powder coat nozzle. Powder Coating is fast becoming the preferred finish for many product applications because they are versatile and environmentally friendly. Once applied, the coating is heated to flow and cure to a hard durable finish. This curing process requires a certain temperature for a certain length of time in order to reach full cure and establish the full film properties for which the material was designed (typically 200°C (390°F) for 10 minutes).
Yes, powder coating is baked onto the metal part, forming a thicker layer of protection that is stronger and more weather-resistant, minimizing scratching, peeling and fading.
We generally aim for a 5 day or less turnaround time. However, due to some variables in the coating process, it can take as long as two weeks.
There are several hundred standard colors and textures to choose from, or we can have your color matched in a custom color lab for an additional charge. For faster turnaround and more competitive pricing, we have many stock colors to choose from. See our stock colors here.
Much more so than paint. The powder is non-toxic and environmentally safe, emitting no or very few harmful VOCs. The entire process at Nortek Powder Coating has been tailored with the environment in mind. Most of our wastewater is evaporated. The most efficient burners and ovens are used in the drying and curing process. Excess powder is often reclaimed and utilized. Learn more here.
As a general rule, our dimensions max out at 84″H x 84″W x 204″L. However, in some instances, we can coat parts that are as long as 22 feet. See the product size capabilities here.
Our blasting capabilities for grit blasting are 48″W x 17″T x 300″L. We also have a manual aluminum oxide room 72″W x 84″T x 228″L.
We specialize in business-to-business medium and large runs, so small production runs (no less than 25 parts) should be repetitive runs.
Many parts that come to us do need blasting before being coated. Our blasting services remove any surface residues before coating to ensure an even application and provide microscopic scoring into the surface of your product to promote a stronger bond with your primer or powder coat. However, if a part is new, clean, and has no mill ⁄ laser scale or corrosion of any kind, we can coat it without any blasting.
We specialize in business-to-business medium and large runs, so small production runs (no less than 25 parts) should be repetitive runs.
Many parts that come to us do need blasting before being coated. Our blasting services remove any surface residues before coating to ensure an even application and provide microscopic scoring into the surface of your product to promote a stronger bond with your primer or powder coat. However, if a part is new, clean, and has no mill ⁄ laser scale or corrosion of any kind, we can coat it without any blasting.
Powder coating pretreatment thoroughly cleans the surfaces of your parts to remove any dust or particles that may interfere with your finish. We use an eight-stage system that cleans your parts and helps improve the bond with your finish. We also employ rapid drying techniques to prevent any corrosion. During pretreatment, we apply a chrome-free zirconium seal enhanced with silane technology to create a firmer grip with primer or powder.
Whether you have products made from aluminum, steel or another metal, priming will help extend the life of your product and coating. Aluminum provides natural resistance to rust and corrosion. Still, if it comes into contact with another metal part or product with conflicting properties, your products can suffer rapid deterioration due to corrosion. Steel and other metals are cost-effective and easy to work with, but when exposed to the elements, they will start to rust fast, destroying your product and the coating. At Nortek, we use an in-line priming system to apply high-quality primers with minimal additional lead time. Our experts know which primers to match with your metals to ensure you gain the maximum advantage, and we only use products from leading manufacturers. For steel products, we use a zinc-rich primer that acts as a galvanizing agent, preventing corrosion from taking hold and strengthening the bond with your powder. For aluminum, our non-zinc primer helps block metal-on-metal contact to stop galvanic corrosion.
Our docks open at 8:30 AM, and close at 4:30 PM, Mon – Fri.
You certainly can have them sent in by UPS or any other common carrier; we can also pick them up for you, or you can drop them off yourself.
The best way is to bring your part to us for evaluation. However, if that is not feasible, you may use our online form. An attached drawing with measurements is required. An isometric drawing is extremely helpful.
Keystone Koating specializes in coating metals. Steel, aluminum, cast iron, cast aluminum, zinc and stainless steel are the most common. We do not have the capability to powder coat wood or plastic.
While any scratch to bare metal is not desirable and does compromise the surface, our research has shown that when parts are processed through our proprietary 8 stage pre-treatment, the applied conversion coating greatly limits the creep of the scratch. In fact, our lab results have shown that an intentionally scratched part will, in some scenarios, rust completely through the steel before coating failure occurs. In addition, if powder coating does get chipped or scratched, there are liquids that can be applied to repair the damage.
Powder coating can last for decades with the right surface preparation, application and powder. Before you coat any metal part, you will want to speak to an expert to ensure you apply a powder capable of withstanding the conditions you are going to put your products through. If your products are intended for use outdoors or under prolonged exposure to sunlight, consider using a primer coat to extend the lifespan of your coating. Ask about our Super Durable Powder made for extra tough climates. And for architectural metal applications, we offer KEYCOAT20, a 20-year limited warranty on AAMA 2605 projects. From start to finish, we use trusted products and processes to ensure quality work you can depend on for years. With over 30 years of experience in the industry, we know which types of powders perform best under any conditions. We use our expertise to make sure your coating exceeds all your expectations. Schedule regular cleaning and maintenance using our suggested methods to help extend the life of your powder coating.
Once applied, powder coating needs to be properly cared for, just like any paint. Usually, a basic cleaning schedule a few times a year will suffice. Some basic tips: Avoid excessive contact. Approach with an attitude of “less is better!” Avoid harsh, abrasive cleaners such as steel wool and scourers. Treat powder coating as you would your car paint. Avoid solvents where possible, When a solvent is absolutely necessary to remove materials from the surface, such as adhesives, the weakest possible solvent should be used (e.g. methylated spirits, white spirits or isopropyl alcohol). A small and unobtrusive area should be tested prior to attempting to use solvents on significant surfaces. After removal of the surface contaminant, the solvent should be dried from the film, and the area that has been wiped with solvent should be washed with a solution of mild liquid detergent and then rinsed with clean water to ensure complete removal of any solvent residues. Under no circumstances should strong solvents be used. Examples of inappropriate chemicals for cleaning or for any contact with powder coating are gasoline, kerosene, MEK, xylene, caustic cleaners like kitchen and bathroom detergents, and paint thinners. Always flush metal that has been exposed to cleaners with copious amounts of fresh, clean water. When a scratch is discovered, it should be addressed immediately. If bare metal is exposed, it should be lightly sanded with a 180 grit or finer sandpaper to remove any corrosion that may be present. Then the sanded area should have all sanding debris removed with either a clean brush or compressed air. The surface can then be touched up with a liquid paint; we recommend a high quality architectural or automotive grade paint, enamels or two part urethane.. Two or three coats of paint are usually required to achieve adequate coverage. For larger areas a liquid primer is recommended.